+ All Categories
Home > Technology > Instructions MEOPTA Ballistic Turret | Optics Trade

Instructions MEOPTA Ballistic Turret | Optics Trade

Date post: 08-Aug-2015
Category:
Upload: optics-trade
View: 432 times
Download: 0 times
Share this document with a friend
68
Ballistic Turret
Transcript
Page 1: Instructions MEOPTA Ballistic Turret | Optics Trade

Ballistic Turret

Page 2: Instructions MEOPTA Ballistic Turret | Optics Trade
Page 3: Instructions MEOPTA Ballistic Turret | Optics Trade

Odšroubujte krytku stávajícího točítka elevace a vyšroubujete oba montážní šrouby. Potom odejměte ovladač a štítek. Krytku s ovladačem a štítkem uschovejte pro případnou zpětnou montáž.

KRYTKA

MONTÁŽNÍ ŠROUBY M 1,6x4

OVLÁDAČ

ŠTÍTEK

Page 4: Instructions MEOPTA Ballistic Turret | Optics Trade

Přiložte rohatku na místo původního ovladače a zašroubujte oba šrouby. Rohatka musí být pevně zafixována.

MONTÁŽNÍ ŠROUBY M 1,6x4ROHATKA

Page 5: Instructions MEOPTA Ballistic Turret | Optics Trade

Nyní našroubujte nákružek na doraz. Nákružek patřičně dotáhněte.

NÁKRUŽEK

Page 6: Instructions MEOPTA Ballistic Turret | Optics Trade

Na nákružek nasuňte posuvnou objímku. Nyní nasuňte hlavici, tak aby při otáčení ve směru hod. ručiček byl doraz na hodnotě -5.

HLAVICE

POSUVNÁ OBJÍMKA

Page 7: Instructions MEOPTA Ballistic Turret | Optics Trade

HLAVICE

POSUVNÁ OBJÍMKA

Vložte pružinu do hlavice a celou sestavu zajistěte centrálním šroubem, který lehce přitáhněte.

CENTRÁLNÍ ŠROUB

PRUŽINA

Page 8: Instructions MEOPTA Ballistic Turret | Optics Trade

POJISTNÉ ŠROUBY

Nyní přitáhněte pojistné šrouby - v posuvné objímce.

Page 9: Instructions MEOPTA Ballistic Turret | Optics Trade

Nastavení:Nastřelte zbraň obvyklým způsobem např. na 100 m. Potom proveďte

částečnou demontáž původního balistického točítka podle návodu. Posuvnou objímku nastavte tak, aby trojúhelníkové indexy byly orientovány v ose puškohledu přímo před vašima očima. Utáhněte čtyři pojistné šrouby pomocí imbusového klíče, který najdete v příslušenství. Povolte centrální šroub o jednu otáčku, povysuňte točítko a natočte ho tak, aby nulový index na stupnici byl v koincidenci s indexy na posuvné objímce. Přitáhněte centrální šroub. Po nastřelení zbraně nastavíme 2. nástřelnou vzdálenost. Pootočte točítkem o patřičný počet kliků proti směru hodinových ručiček . Po stlačení aretačního tlačítka natočte první prstenec svým indexem proti indexům na posuvné objímce a uvolněte aretační tlačítko. Počet potřebných kliků zjistíte pomocí balistického programu, nebo nastřelením. Pro 3. nástřelnou vzdálenost použijeme stejný postup jako pro druhé točítko. Vaše balistické točítko je nyní připraveno k použití.

Page 10: Instructions MEOPTA Ballistic Turret | Optics Trade

Funkce:Pro nastavení příslušné vzdálenosti natočte hlavici balistického točítka

požadovaným indexem proti nulovým indexům na posuvné objímce. Počet potřebných kliků můžete rovněž zjistit pomocí našeho balistického programu. Počet kliků se odpočítává vždy od základní polohy nulových indexů na posuvné objímce.

Page 11: Instructions MEOPTA Ballistic Turret | Optics Trade

Remove the existing elevation turret cap and unscrew the two mounting screws. Then remove the actuator and the shield. Keep the cap, actuator and shield at a safe place for future reassembly.

CAP

MOUNTING SCREWS M 1,6x4

ACTUATOR

SHIELD

Page 12: Instructions MEOPTA Ballistic Turret | Optics Trade

Put the ratchet wheel to the place of the original actuator and screw in the two screws. The ratchet wheel must be firmly fixed.

MOUNTING SCREWS M 1,6x4

RATCHET WHEEL

Page 13: Instructions MEOPTA Ballistic Turret | Optics Trade

Screw in the collar as far as it will go. Tighten the collar properly.

COLLAR

Page 14: Instructions MEOPTA Ballistic Turret | Optics Trade

Put the sliding sleeve onto the collar. Now slide in the head so that when turning clockwise, the stop is on digit -5.

HEAD

SLIDING SLEEVE

Page 15: Instructions MEOPTA Ballistic Turret | Optics Trade

Insert the spring into the head and secure the assembly with the central screw; tighten it gently.

CENTRAL SCREW

SPRING

Page 16: Instructions MEOPTA Ballistic Turret | Optics Trade

LOCKING SCREWS

Screw in the locking screws in the sliding sleeve and secure in position.

Page 17: Instructions MEOPTA Ballistic Turret | Optics Trade

Adjustment:Use the standard procedure for sighting-in the rifle, e.g. at a 100 m

distance. Then, following the instructions, partially disassemble the original ballistic turret. Adjust the sliding sleeve so that the vertical index line is in the axis of the riflescope directly before your eyes. Tighten the four locking screws with the Allen wrench from the accessory bag. Loosen the central screw one turn, pull out the turret a little and turn it so that the zero index on the turret coincides with the index on the sliding sleeve and, at the same time, is in the stop position. Tighten the locking screws. Tighten the central screw. The initial sighting-in distance is also the stop position. After the initial adjustment, make the adjustment for the 2nd sighting-in distance. Turn the turret counterclockwise by the required number of clicks. Turn the first ring so that its index faces the zero index on the turret; secure in position with the locking screw. The number of clicks may be determined using our ballistic program or by sighting-in. When adjusting the 3rd sighting-in distance, use the same

Page 18: Instructions MEOPTA Ballistic Turret | Optics Trade

procedure as for the second turret. Your ballistic turret is now ready for use.

Features: To adjust the corresponding distance, turn the entire ballistic turret

with its zero index against the required mark (red, green).Should you desire to sight-in the riflescope at an additional distance,

you may adjust this additional distance by turning the turret against the vertical index on the sliding sleeve. The required number of clicks may also be determined using our ballistic program. The number of clicks is always calculated from the initial position - with the zero index on the turret against the vertical index of the sliding sleeve.

Page 19: Instructions MEOPTA Ballistic Turret | Optics Trade

Die Abdeckung der Taste Elevation abschrauben und beide Montag-eschrauben herausschrauben. Danach Bedienung und Schild abne-hmen. Die Abdeckung und die Bedienung mit Schild für eventuellen Wiederanbau aufbewahren.

ABDECKUNG

MONTAGESCHRAUBEN M 1,6x4

BEDIENUNG

SCHILD

Page 20: Instructions MEOPTA Ballistic Turret | Optics Trade

Die Ratsche an der Stelle der Bedienung anlegen und beide Schrauben einschrauben. Die Ratsche muss fest fixiert sein.

MONTAGESCHRAUBEN M 1,6x4

RATSCHE

Page 21: Instructions MEOPTA Ballistic Turret | Optics Trade

Nun den Ring auf Anschlag schrauben. Den Ring festziehen.

RING

Page 22: Instructions MEOPTA Ballistic Turret | Optics Trade

Auf den Ring die Schiebehülse aufsetzen.Nun den Kopf so aufschieben, dass sich beim Drehen in Uhrzeiger-richtung der Anschlag auf dem Wert -5 liegt.

KOPF

SCHIEBEHÜLSE

Page 23: Instructions MEOPTA Ballistic Turret | Optics Trade

Die Feder im Kopf einlegen und die gesamte Gruppe mit leicht fes-tgezogener Zentralschraube sichern.

ZENTRALSCHRAUBE

FEDER

Page 24: Instructions MEOPTA Ballistic Turret | Optics Trade

SICHERUNGSS-CHRAUBEN

Nun die Sicherungsschrauben in die Schiebehülse schrauben und die Position sichern.

Page 25: Instructions MEOPTA Ballistic Turret | Optics Trade

Einstellen:Mit der Waffe wie üblich, z.B. auf 100 m schießen. Danach den

ballistischen Drehknopf nach Anleitung teilweise demontieren. Die Schiebehülse so einstellen, dass der vertikale Indexstrich in der Zielfernrohrachse direkt vor Ihren Augen liegt. Die vier Sicherungsschrauben mit Inbusschlüssel aus dem Zubehör festziehen. Die Zentralschraube um eine Umdrehung lösen, den Drehknopf herausziehen und so drehen, dass der Nullindex in Koinzidenz mit dem Index auf der Schiebehülse und gleichzeitig auf Anschlag ist.

Die Sicherungsschrauben anziehen. Die Zentralschraube festziehen. Die grundlegende Schussentfernung ist gleichzeitig Anschlagposition.

Nach Einstellen der Grundeinstellung die 2. Schussentfernung einstellen. Den Drehknopf die entsprechende Anzahl Klicks entgegen der Uhrzeigerrichtung drehen. Den ersten Ring mit seinem Index gegen den Nullindex einstellen und diese Stellung mit Sicherheitsschraube sichern. Die entsperechende Anzahl der Klicks mit ballistischem

Page 26: Instructions MEOPTA Ballistic Turret | Optics Trade

Programm oder durch Schießn ermitteln. Für die 3. Schussentfernung das gleiche Vorgehen auch für den

zweiten Drehknopf benutzen. Ihr ballistischer Drehknopf ist zur Benutzung bereit.

Funktionen: Für das Einstellen der zugehörigen Entfernung den ganzen

ballistischen Drehknopf mit Nullindex gegen das gewünschte Zeichen (rot, grün) stellen.

Wenn Sie eine zusätzliche Schussentfernung wünschen, können Sie eine weitere Entfernung durch Drehen des Knopfes gegen vertikalen Index auf der Schiebehülse einstellen. Die Anzahl der erforderlichen Klicks können Sie ebenfalls mit Hilfe unseres ballistischen Programms ermitteln. Die Anzahl der Klicks wird immer aus der Grundstellung des Nullindexes auf dem Drehknopf gegen den vertikalen Index auf der Schiebehülse berechnet.

Page 27: Instructions MEOPTA Ballistic Turret | Optics Trade

Desenrosque la tapa de la existente torreta de elevación y destornille los dos tornillos de montaje. A continuación retire el elemento de control y la placa. Guarde la tapa con el elemento de control y con la placa por si desea volver a montarlos en el futuro.

TAPA

TORNILLOS DE MONTAJE M 1,6x4

ELEMENTO DE CONTROL

PLACA

Page 28: Instructions MEOPTA Ballistic Turret | Optics Trade

Coloque el trinquete en el lugar del elemento de control original y atornille los dos tornillos. El trinquete debe estar firmemente sujeto.

TORNILLOS DE MONTAJE M 1,6x4

TRINQUETE

Page 29: Instructions MEOPTA Ballistic Turret | Optics Trade

Ahora enrosque el collarín hasta que haga tope. Apriete el collarín firmemente.

COLLARÍN

Page 30: Instructions MEOPTA Ballistic Turret | Optics Trade

Inserte la virola móvil en el collarín.Ahora inserte la cabeza de modo que al girar en el sentido de las agujas de reloj el tope esté en la cifra -5.

CABEZA

VIROLA MÓVIL

Page 31: Instructions MEOPTA Ballistic Turret | Optics Trade

Inserte el muelle en la cabeza y asegure todo el conjunto con el tornillo central, apretándolo suavemente.

TORNILLO CENTRAL

MUELLE

Page 32: Instructions MEOPTA Ballistic Turret | Optics Trade

TORNILLOS DE SEGURIDAD

Nun die Sicherungsschrauben in die Schiebehülse schrauben und die Position sichern.

Page 33: Instructions MEOPTA Ballistic Turret | Optics Trade

Ajuste:Realice los tiros de ajuste como acostumbra, p.ej. a 100 metros de

distancia. A continuación desmonte parcialmente la torreta balística original de acuerdo con las instrucciones. Ajuste la virola móvil de manera que la línea de índice vertical esté en línea con el eje de la mira telescópica justo delante de sus ojos. Apriete los cuatro tornillos de seguridad con una llave Allen, incluida en la bolsa de accesorios. Afloje el tornillo central un giro, saque parcialmente la torreta y gírela de manera que el índice de cero en la torreta coincida con el índice en la virola móvil y, al mismo tiempo, esté en el tope.

Apriete los tornillos de seguridad. Apriete el tornillo central. La distancia básica para los tiros de ajuste es también la posición de tope.

Una vez finalizada la puesta a punto básica, realice el procedimiento para la 2a distancia para los tiros de ajuste. Gire la torreta el sentido contrario a las agujas del reloj para que haga el número requerido de clics. Gire la primera anilla para que su índice esté contra el índice cero en

Page 34: Instructions MEOPTA Ballistic Turret | Optics Trade

la torreta y asegure esta posición con el tornillo de seguridad. El número necesario de clics lo determinará mediante un programa balístico o realizando los tiros de ajuste.

En cuanto a la 3a distancia para los tiros de ajuste, utilice el mismo procedimiento que para la segunda torreta.

Su torreta balística está lista para usar.

Funcionamiento: Para ajustar la distancia correspondiente gire toda la torreta balística

para que su índice cero esté contra la marca correspondiente (roja, verde).

Si desea realizar los tiros de ajuste a distancias adicionales, puede hacerlo girando la torreta contra el índice vertical en la virola móvil. El número necesario de clics lo puede determinar también usando nuestro programa balístico. El número de clics se calcula siempre partiendo de la posición básica - con el índice de cero en la torreta contra el índice vertical en la virola móvil.

Page 35: Instructions MEOPTA Ballistic Turret | Optics Trade

Desaperte a tampa do ajuste de elevação existente e desaparafuse os dois parafusos de montagem. Depois, retire o anel e a anilha. Guarde a tampa com o anel e a anilha para uma eventual remontagem.

TAMPA

PARAFUSOS DE MONTAGEM

ANEL

ANILHA

Page 36: Instructions MEOPTA Ballistic Turret | Optics Trade

Fixe o roquete no lugar do anel original e aperte os dois parafusos. O roquete deve ser fixado de modo firme.

PARAFUSOS DE MONTAGEM M1, 6x4

ROQUETE

Page 37: Instructions MEOPTA Ballistic Turret | Optics Trade

Agora aparafuse o espigão até ao batente. Aperte bem o espigão.

ESPIGÃO

Page 38: Instructions MEOPTA Ballistic Turret | Optics Trade

Coloque o espigão na manga ajustável.Agora enfie a cabeça de modo que ao girar no sentido dos ponteiros do relógio o batente fique no valor -5.

CABEÇA

MANGA AJUSTÁVEL

Page 39: Instructions MEOPTA Ballistic Turret | Optics Trade

Coloque a mola na cabeça e fixe todo o conjunto com o parafuso central que deve ser apertado ligeiramente.

PARAFUSO CENTRAL

MOLA

Page 40: Instructions MEOPTA Ballistic Turret | Optics Trade

PARAFUSOS DE FIXAÇÃO

Agora aperte os parafusos de fixação na manga ajustável e fixe a posição.

Page 41: Instructions MEOPTA Ballistic Turret | Optics Trade

Configuração:Calibre a arma como de costume, por ex. para 100m. A seguir

desmonte parcialmente o ajuste balístico original de acordo com as instruções. Defina a manga ajustável de modo que a linha de vértice vertical esteja no eixo da luneta diante dos seus olhos. Aperte os quatro parafusos de fixação com a chave hexagonal que encontrará nos acessórios. Desaperte o parafuso central girando-o uma vez, puxe o ajuste e gire-o de modo a que o índice zero do ajuste coincida com o índice na manga ajustável e ao mesmo tempo esteja no batente.

Aperte os parafusos de fixação. Aperte o parafuso central. A distância de calibragem básica é também a posição do batente.

Uma vez definida a configuração básica, definimos também a segunda distância de calibragem. Gire o ajuste o número apropriado de cliques, no sentido contrário ao dos ponteiros do relógio. Rode o primeiro anel de modo que o seu índice esteja frente ao índice zero no ajuste e fixe esta posição com o parafuso de fixação. Para descobrir o número de cliques

Page 42: Instructions MEOPTA Ballistic Turret | Optics Trade

necessários utilize o programa balístico ou a calibragem. O mesmo procedimento será aplicado para a 3ª distância de

calibragem e para o segundo ajuste. O vosso ajuste balístico está pronto para usar.

Funções: Para definir a distância gire o ajuste balístico de modo a que o índice

zero corresponda à marca desejada (vermelha, verde).Caso deseje mais distâncias de calibragem, pode definir mais

distâncias do ajuste correspondentes ao índice vertical da manga ajustável. Para descobrir o número de cliques necessários utilize o nosso programa balístico. O número de cliques é calculado a partir da posição básica-índice zero, no ajuste correspondente ao índice vertical na manga ajustável.

Page 43: Instructions MEOPTA Ballistic Turret | Optics Trade

Dévissez le couvercle de la tourelle d’élévation existante et retirez les deux vis de montage. Puis ôtez la commande et la plaque. Gardez le couvercle et la plaque pour un remontage éventuel.

COUVERCLE

VIS DE FIXATION M 1,6x4

COMMANDE

PLAQUE

Page 44: Instructions MEOPTA Ballistic Turret | Optics Trade

Fixez le cliquet au lieu de la commande d’origine et vissez les deux vis. Le cliquet doit être solidement fixé.

VIS DE FIXATION M1,6x4

CLIQUET

Page 45: Instructions MEOPTA Ballistic Turret | Optics Trade

Maintenant vissez le collet jusqu’au bout. Serrez correctement le collet.

COLLET

Page 46: Instructions MEOPTA Ballistic Turret | Optics Trade

Enfilez le manchon coulissant sur le collet.Maintenant, faites glisser la tête de sorte à atteindre la valeur de la butée de -5 lorsque vous tournez dans le sens horaire.

TÊTE

MANCHON COULISSANT

Page 47: Instructions MEOPTA Ballistic Turret | Optics Trade

Insérez le ressort dans la tête et fixez tout l’assemblage par la vis centrale, serrez la vis doucement.

VIS CENTRALE

RESSORT

Page 48: Instructions MEOPTA Ballistic Turret | Optics Trade

VIS DE BLOCAGE

Maintenant serrez les vis de blocage dans le manchon coulissant et fixez la position.

Page 49: Instructions MEOPTA Ballistic Turret | Optics Trade

Réglage:Réglez l’arme comme d’habitude à 100 m. Puis faites un démontage

partiel de la tourelle balistique original selon les instructions. Réglez le manchon coulissant de sorte que la ligne de repère verticale soit dans l’axe des lunettes de tir juste devant vos yeux. Serrez les quatre vis de blocage avec une clé Allen qui se trouve dans les accessoires. Desserrez la vis centrale d’un tour, tirez la tourelle et tournez-la de sorte que l’indice zéro sur la tourelle soit en coïncidence avec l’indice sur le manchon coulissant et soit également en butée.

Serrez les vis de blocage. Serrez la vis centrale. La distance de réglage de base représente également la position d’arrêt.

Après avoir effectué le réglage de base, réglez la 2ème distance. Tournez la tourelle d’un nombre approprié de clics dans le sens antihoraire. Tournez la première bague avec son indice contre l’indice zéro et fixez cette position par la vis de blocage. Vous déterminerez le nombre de clics nécessaires à l’aide du programme balistique ou du

Page 50: Instructions MEOPTA Ballistic Turret | Optics Trade

réglage Pour la 3ème distance, utilisez le même procédé comme pour la

deuxième tourelle. Votre tourelle balistique est prête à l’emploi.

Fonction: Pour régler la distance appropriée, tournez toute la tourelle balistique

par l’indice zéro contre le repère souhaité (rouge, vert).Si vous souhaitez d’autres distances de réglage, vous pouvez régler

les distances supplémentaires de rotation de la tourelle contre l’indice vertical sur le manchon coulissant. Vous pouvez déterminer le nombre de clics nécessaires à l’aide de notre programme balistique. Le nombre de clics est calculé à partir de la position initiale - l’indice zéro sur la tourelle contre l’indice vertical sur le manchon coulissant.

Page 51: Instructions MEOPTA Ballistic Turret | Optics Trade

Svitare il coperchio della manopola di elevazione esistente e le due viti di montaggio. Poi rimuovere il regolatore e la targhetta. Conservare il coperchio con il regolatore e la targhetta per il rimontaggio eventuale.

COPERCHIO

VITI DI MONTAGGIO M 1,6x4

REGOLATORE

TARGHETTA

Page 52: Instructions MEOPTA Ballistic Turret | Optics Trade

Collocare la ruota d’arresto al posto del regolatore e avvitare le due viti. La ruota d’arresto deve essere saldamente fissata.

VITI DI MONTAGGIO M1,6x4

RUOTA D’ARRESTO

Page 53: Instructions MEOPTA Ballistic Turret | Optics Trade

Ora avvitare il collare fino in fondo. Stringere correttamente il collare.

COLLARE

Page 54: Instructions MEOPTA Ballistic Turret | Optics Trade

Infilare il manicotto scorrevole nel collare.Ora infilare la testa, in modo che, ruotando in senso orario, il valore di arresto sia -5.

TESTA

MANICOTTO SCORREVOLE

Page 55: Instructions MEOPTA Ballistic Turret | Optics Trade

Inserire la molla nella testa e fissare l’intero sistema con la vite centrale, stringendola leggermente.

VITE CENTRALE

MOLLA

Page 56: Instructions MEOPTA Ballistic Turret | Optics Trade

VITI DI BLOCCAGGIO

Ora serrare le viti di bloccaggio nel manicotto scorrevole e assicurare la posizione.

Page 57: Instructions MEOPTA Ballistic Turret | Optics Trade

Impostazione:Sparare con l’arma nel modo consueto, ad es. a 100 m. Quindi eseguire

il parziale smontaggio della manopola balistica originale secondo le istruzioni. Impostare il manicotto scorrevole in modo che la linea d’indice verticale, nell’asse del cannocchiale dell’arma, si trovi proprio davanti agli occhi. Serrare le quattro viti di bloccaggio con una chiave a brugola, che fa parte degli accessori. Allentare la vite centrale di un giro, tirare e ruotare la manopola in modo che l’indice zero della manopola stessa coincida con l’indice sul manicotto scorrevole e si trovi nel contempo sull’arresto.

Serrare le viti di bloccaggio. Stringere la vite centrale. La distanza di tiro iniziale è anche la posizione di arresto.

Dopo aver eseguito l’impostazione iniziale, impostiamo la seconda distanza di tiro. Ruotare la manopola per il numero appropriato di clic in senso antiorario. Ruotare il primo anello con l’indice in senso opposto all’indice zero sulla manopola e fissare questa posizione con la vite di

Page 58: Instructions MEOPTA Ballistic Turret | Optics Trade

bloccaggio. Il numero di clic necessari si può determinare mediante il programma balistico o sparando.

Per la terza distanza di tiro utilizziamo la stessa procedura anche per la seconda manopola.

La manopola balistica è pronta per l’uso.

Funzioni: Per impostare la distanza adeguata, girare l’intera manopola balistica

con l’indice zero opposto al segno richiesto (rosso, verde).Se si desiderano ulteriori distanze di tiro, è possibile impostare le altre

distanze ruotando la manopola in senso opposto all’indice verticale sul manicotto scorrevole. Il numero di clic necessari si può determinare anche mediante il nostro programma balistico. Il numero di clic viene calcolato sempre dalla posizione iniziale-indice zero sulla manopola rispetto all’indice verticale sul manicotto scorrevole.

Page 59: Instructions MEOPTA Ballistic Turret | Optics Trade

Открутите крышку установленного маховика и открутите оба монтажных винта. Снимите регулятор и заслон. Крышку вместе с регулятором и заслоном сохраните на случай обратного монтажа.

КРЫШКА

МОНТАЖНЫЕ ВИНТЫ M 1,6x4

РЕГУЛЯТОР

ЗАСЛОН

Page 60: Instructions MEOPTA Ballistic Turret | Optics Trade

Поставьте храповик на место первоначального регулятора и закрутите оба винта. Храповик должен быть надежно зафиксирован.

МОНТАЖНЫЕ ВИНТЫ M 1,6x4

ХРАПОВИК

Page 61: Instructions MEOPTA Ballistic Turret | Optics Trade

Теперь прикрутите кольцо к упору. Кольцо должно быть соответствующим образом зажато.

КОЛЬЦО

Page 62: Instructions MEOPTA Ballistic Turret | Optics Trade

На храповик наденьте подвижную муфту.Теперь наденьте головку таким образом, чтобы при поворачивании по часовой стрелке упор был на значении -5.

ГОЛОВКА

ПОДВИЖНАЯ МУФТА

Page 63: Instructions MEOPTA Ballistic Turret | Optics Trade

Вставьте пружину в головку и весь комплект маховика зафиксируйте центральным винтом, слегка его зажав.

ЦЕНТРАЛЬНЫЙ ВИНТ

ПРУЖИНА

Page 64: Instructions MEOPTA Ballistic Turret | Optics Trade

ПРЕДОХРАНИТЕЛЬНЫЕ БОЛТЫ

Теперь закрутите предохранительные болты в подвижной муфте и зафиксируйте в нужном положении.

Page 65: Instructions MEOPTA Ballistic Turret | Optics Trade

Настройка:Пристреляйте ваше оружие обычным способом, напр., на 100 м. Потом

частично демонтируйте первоначальный баллистический маховик, как это описано в инструкции. Подвижную муфту отрегулируйте так, чтобы вертикальный индекс был в одной оси прицела прямо перед вашими глазами. Зажмите четыре предохранительных болта с помощью ключа, поставляемого в комплекте. Ослабьте центральный винт на один оборот, слегка приподнимите маховик и поверните его так, чтобы нулевой индекс на маховике совпадал с индексом на подвижной муфте и одновременно был на упоре.

Зажмите предохранительные болты. Зажмите центральный винт. Базовое пристрелянное расстояние одновременно является положением упора.

После проведения базовой настройки проведем настройку 2-ого пристрелянного расстояния. Поверните маховик на соответствующее количество щелчков против часовой стрелки. Поставьте индекс первой торцевой шайбы напротив нулевого индекса на маховике и

Page 66: Instructions MEOPTA Ballistic Turret | Optics Trade

зафиксируйте данное положение с помощью предохранительного болта. Количество необходимых щелчков выясните с помощью баллистической программы или с помощью пристрелки.

Для настройки 3-его пристрелянного расстояния повторяем вышеописанную последовательность со вторым маховиком.

Ваш баллистический маховик готов к эксплуатации.

Функции: Для настройки необходимого расстояния поверните весь маховик так,

чтобы его нулевой индекс стоял на нужной отметке (красная, зеленая).Если вы хотите пристрелять дополнительные расстояния, то

настройте другие расстояния, поворачивая маховик по отношению к вертикальному индексу на подвижной муфте. Количество необходимых щелчков можно также установить с помощью нашей баллистической программы. Количество щелчков считаем от базового положения – нулевого индекса на маховике по отношению к индексу на подвижной муфте.

Page 67: Instructions MEOPTA Ballistic Turret | Optics Trade

392 8654 90051 Ballistic turret MEOSTAR 30 -BPZD Meostar R1 3-12x56

PZD Meostar R1 3-12x56 RD

392 8654 90052 Ballistic turret MEOSTAR 35 -B

PZD Meostar R1 4-12x40

PZD Meostar R1r 3-12x56

PZD Meostar R1r 3-12x56 RD

PZD Meostar R1r 3-12x56 RGD

PZD Meostar R1r 3-12x56 RD/MR

392 8654 90053 Ballistic turret MEOSTAR 40 -B PZD Meostar R1 3-10x50

392 8654 90054 Ballistic turret MEOSTAR 50 -B

PZD Meostar R1 1-4x22

PZD Meostar R1 1-4x22 RD

PZD Meostar R1 1-4x22 RD/MR

392 8654 90055 Ballistic turret MEOSTAR 60 -B PZD Meostar R1 1,5-6x42 RD

392 8654 90056 Ballistic turret MEOSTAR 80 -B PZD Meostar R1 1,5-5x20

Page 68: Instructions MEOPTA Ballistic Turret | Optics Trade

Meopta - optika, s.r.o.Kabelíkova 1750 02 Přerov

Tel. 581 242 281Fax: 581 242 222

E-mail: [email protected]

418040

Duben 2013, Rev. 01


Recommended