Date post: | 02-Nov-2015 |
Category: |
Documents |
Upload: | foster3332 |
View: | 217 times |
Download: | 0 times |
1OFFICE:panielova 1315/25, Praha 6, 163 00IO: 64940799DI: CZ64940799
SHOWROOM:Sdlit Jantejn 39, Horn Dubenky588 52
SHADOWS PC929Suspension Light PC929
Components included with unit:
5x plastic grommet, 2x hex screw, 1x hex key, 3x wire connector terminal, 5x light source, 5x glass shade, 5x wooden body, 1x metal ceiling canopy with ceiling hanger, 5x silicone pad
Installation Steps:
1. Install the hanger for the metal ceiling canopy (fig. 1). - With regard for various types of ceiling materials, we recommend consulting an expert when securing the canopy hanger to the ceil-ing. The manufacturer assumes no liability for incorrect installation or defects in the material to which the canopy hanger is to be se-cured.
Because the glass components of the light are hand-crafted, there is some variation in the inner diameter of the individual shades. Therefore, each shade is carefully matched to its respec-tive wooden body prior to shipping. The correct match is indi-cated with colored rubber bands. During assembly, care must be taken to ensure that each shade is paired with the wooden body of the corresponding colored rubber band (fig. 2b).
2. Light Assembly- Select one of the glass shades and its corresponding wooden body. - Attach the glass shade to the wooden body by pulling the power cord through the shade.- If the shade is slightly misaligned, try carefully turning it on the wooden body, or correct the misalignment with one of the silicone pads by adhering it to the outer side of the wooden body so that it is situated between the shade and body (fig. 2a). - Pull the power cords of the individual lights through the metal ceiling canopy and secure them using the plastic grommets. - Connect the light to the building wiring. - Using the hex screws and the hex key, attach the ceiling canopy to the ceiling hanger (fig. 1).
1. Install the hanger for the metal ceiling canopy (fig. 1). - With regard for various types of ceiling materials, we recommend consulting an expert when securing the canopy hanger to the ceil-ing. The manufacturer assumes no liability for incorrect installation or defects in the material to which the canopy hanger is to be se-cured.
3. Restore power at the main circuit panel and ensure that the light is working properly.
280
170
2000
400x 60
2Materials
Glass:The technological methods used in creating the light are based on several hundred years of traditional Czech handmade glass production. Respect for the material and its traditional production is characteristic for Bro-kis. Imperfections in the glass are the result of these technological methods and have no effect on the quality or functionality of the light.Wood: wooden body made of European oak (QUERCUS SPP)Wood is a natural material that reacts to changes in relative humidity levels and temperature in the sur-rounding environment. When the relative humidity is extremely low (below 30%), the wood gradually dries out and cracks will appear. Therefore, we recommend maintaining a relative humidity of between 40-60% and a temperature of 15 to 25 degrees Celsius.
Cleaning The light may be cleaned with common cleaning agents. Do not use solvents or abrasive cleaning agents (powders).
Prior to shipping, the functionality of each light and its components is thoroughly tested. The manu-facturer assumes no liability for the mishandling of products.
Technical support: [email protected]
1a
2a 2b
M4 screws
M4 screws
canopy cover
cealing rack
Use this holes for the fixing rack onto the ceiling.
1OFFICE:panielova 1315/25, Praha 6, 163 00IO: 64940799DI: CZ64940799
SHOWROOM:Sdlit Jantejn 39, Horn Dubenky588 52
SHADOWS PC929Svtidlo visac PC929 Komponenty, kter jsou soust balen:
5x plastov prchodka, 2x imbusov roub, 1x imbusov kl, 3x pipojovac svorkovnice, 5x svteln zdroj, 5x sklenn stnidlo, 5x devn montura, 1x kovov baldachn vetn drku, 5x siliko-nov oka
Montn postup:
Mont sm provdt pouze pracovnk sodbornou elektrotech-nickou kvalifikac.Ped mont vypnte pslunm jistiem pvod elektrickho proudu!Pi nedodren montnho nvodu vrobce neru za ppadn vznikl kody!
Vnitn prmry jednotlivch stntek se mrn li; to je pirozenm dsledkem run vroby sklennch st svtla. Ztoho dvodu je kad stntko ped expedic peliv prov-no s pslunou devnou monturou. Sprvn kombinace je vyznaena barevnmi gumikami. Pi kompletaci je proto nez-bytn dodret shodnost barevnho oznaen sklennho stntka a devn montury (obr. 2b).
2. Kompletace svtla.- Vyberte sprvnou kombinaci sklennho stntka a devn mon-tury. - Prothnte napjec kabel skrz sklenn stnidlo a usate devnou monturu.- Pokud je sklo mrn vyoseno, opatrn s nm na devn montue pootote, poppad pouijte silikonovou oku (obr. 2a), kterou nalepte na vnj st devn montury (mezi sklo a devnou mon-turu).- Elektrick kabely jednotlivch svtidel prothnte kovovm balda-chnem a zafixujte zajiovacmi plastovmi oky. - Zite elektrick propojen svtidla s elektroinstalac. - Pomoc imbusovch roubk a imbusovho kle piroubujte bal-dachn kstropnmu drku (obr. 1).
1. Ke stropu piroubujte drk stropnho baldachnu (obr. 1). - S ohledem na rzn typ i st materil strop doporuujeme mont konzultovat s odbornkem. Vrobce svtidla neodpovd za nevhodn zvolen pracovn postup i vady materilu, do kterho se nosn komponent instaluje.
3. Zapnte pslun jisti a ovte funknost svtidla.
280
170
2000
400x 60
2Uit materily
Sklo:Uit technologick postupy vychzej z nkolikasetlet tradice esk rukodln sklsk vroby. Tento respekt kmaterilu a jeho tradin vrob je pro firmu Brokis pznan. Ppadn nedo-konalosti skla jsou zapinny zvolenmi technologickmi postupy a nemaj vliv na kvalitu a funknost svtidel.
Devo: montura zdubu evropskho (QUERCUS SPP)Devo je prodn materil, kter reaguje na zmny okolnho prosted zejmna vlhkosti a teploty. Pi extrmn nzk relativn vlhkosti vzduchu (pod 30 %) dochz k vysychn deva a nsledn tvorb trhlin. Proto doporuujeme udrovat relativn vlhkost vzduchu mezi 40 - 60 % a teplotu od 15 do 25 C.itn Svtidlo je mon oetovat bnmi isticmi prostedky. Nepouvejte rozpoutdla a abrazivn istic prostedky (prky).
U kadho svtidla vetn jeho komponent je ped expedic dkladn zkontrolovna funknost. Vrobce nenese odpovdnost za nesprvn zachzen sprodukty.
Technick podpora: [email protected]
1a
2a 2b
M4 screws
M4 screws
canopy cover
cealing rack
Use this holes for the fixing rack onto the ceiling.
PC929_enPC929_cz.pdf