The Appendix is an integral part of Certificate of Accreditation No. 73/2019 of 12/02/2019 Accredited entity according to ČSN EN ISO/IEC 17025:2018: České vysoké učení technické v Praze Faculty of Civil Engineering – Testing Laboratory Thákurova 7, 166 29 Praha 6 Page 1 of 16 11_01-P508_L-20130510 Testing laboratory locations: 1. OL 123 Building Materials Laboratory Thákurova 7, 166 29 Praha 6 2. OL 124 Building Structures Laboratory Thákurova 7, 166 29 Praha 6 3. OL 132 Structural Mechanics Laboratory Thákurova 7, 166 29 Praha 6 4. OL 133 Concrete Structures Laboratory Thákurova 7, 166 29 Praha 6 5. OL 134 Steel Structures Laboratory Thákurova 7, 166 29 Praha 6 6. OL 136 Road Structures Laboratory Thákurova 7, 166 29 Praha 6 7. OL 137 Railway Structures Laboratory Thákurova 7, 166 29 Praha 6 8. OL 181 Experimental Centre Laboratory (FSv) Thákurova 7, 166 29 Praha 6 9. OL 181 Experimental Centre Laboratory Třinecká 1024, (UCEEB) 273 43 Buštěhrad 10. OL 182 Experimental Geotechnics Chotilsko-Smilovice 93, Centre Laboratory 263 01 Dobříš 1. OL 123 Building Materials Laboratory Tests: Ordinal number 1 Test procedure/ method name Test procedure/ method identification 2 Tested object 123/1 Determination of flexural strength ČSN EN 12372 ČSN EN 14617-2 Stone and artificial stone 123/2 Determination of bulk density ČSN EN 14617-1 Stone and artificial stone 123/3 Determination of water absorption ČSN EN 1925 ČSN EN 13755 ČSN EN 14617-1 Stone and artificial stone 123/4 Determination of resistance to frost ČSN EN 12371 ČSN EN 14617-5 Stone and artificial stone 123/5 Determination of compressive strength ČSN EN 1926 ČSN EN 14617-15 Stone and artificial stone 123/6 Determination of water retention ČSN EN 413-2 Binder, mortar 123/7 Determination of water vapour permeability ČSN EN 1015-19 ČSN EN 12086 ČSN EN 772-15 ČSN EN ISO 7783 ČSN EN ISO 12572 Mortars, thermal insulation products, masonry units, coating materials, building materials and products 123/8 Determination consistency - degree of compactibility ČSN EN 12 350-4 Fresh concrete 123/9 Determination consistency by flow table test ČSN EN 12 350-5 Fresh concrete
Transcript
The Appendix is an integral part of
Certificate of Accreditation No. 73/2019 of 12/02/2019
Accredited entity according to ČSN EN ISO/IEC 17025:2018:
České vysoké učení technické v Praze Faculty of Civil Engineering – Testing Laboratory
Thákurova 7, 166 29 Praha 6
Page 1 of 16 11_01-P508_L-20130510
Testing laboratory locations:
1. OL 123 Building Materials Laboratory Thákurova 7, 166 29 Praha 6
2. OL 124 Building Structures Laboratory Thákurova 7, 166 29 Praha 6
3. OL 132 Structural Mechanics Laboratory Thákurova 7, 166 29 Praha 6
4. OL 133 Concrete Structures Laboratory Thákurova 7, 166 29 Praha 6
5. OL 134 Steel Structures Laboratory Thákurova 7, 166 29 Praha 6
6. OL 136 Road Structures Laboratory Thákurova 7, 166 29 Praha 6
7. OL 137 Railway Structures Laboratory Thákurova 7, 166 29 Praha 6
8. OL 181 Experimental Centre Laboratory (FSv) Thákurova 7, 166 29 Praha 6
9. OL 181 Experimental Centre Laboratory Třinecká 1024,
(UCEEB) 273 43 Buštěhrad
10. OL 182 Experimental Geotechnics Chotilsko-Smilovice 93,
Centre Laboratory 263 01 Dobříš
1. OL 123 Building Materials Laboratory
Tests:
Ordinal number
1
Test procedure/ method name
Test procedure/ method identification
2
Tested object
123/1 Determination of flexural
strength
ČSN EN 12372
ČSN EN 14617-2
Stone and artificial stone
123/2 Determination of bulk
density
ČSN EN 14617-1 Stone and artificial stone
123/3 Determination of water
absorption
ČSN EN 1925
ČSN EN 13755
ČSN EN 14617-1
Stone and artificial stone
123/4 Determination of resistance
to frost
ČSN EN 12371
ČSN EN 14617-5
Stone and artificial stone
123/5 Determination of
compressive strength
ČSN EN 1926
ČSN EN 14617-15
Stone and artificial stone
123/6 Determination of water
retention
ČSN EN 413-2 Binder, mortar
123/7 Determination of water
vapour permeability
ČSN EN 1015-19
ČSN EN 12086
ČSN EN 772-15
ČSN EN ISO 7783
ČSN EN ISO 12572
Mortars, thermal insulation
products, masonry units,
coating materials, building
materials and products
123/8 Determination consistency -
degree of compactibility
ČSN EN 12 350-4 Fresh concrete
123/9 Determination consistency
by flow table test
ČSN EN 12 350-5 Fresh concrete
The Appendix is an integral part of
Certificate of Accreditation No. 73/2019 of 12/02/2019
Accredited entity according to ČSN EN ISO/IEC 17025:2018:
České vysoké učení technické v Praze Faculty of Civil Engineering – Testing Laboratory
Thákurova 7, 166 29 Praha 6
Page 2 of 16 11_01-P508_L-20130510
Ordinal number
1
Test procedure/ method name
Test procedure/ method identification
2
Tested object
123/10 Determination consistency
by Vebe test
ČSN EN 12 350-3 Fresh concrete
123/11 Determination consistency
by slump test
ČSN EN 12 350-2 Fresh concrete
123/12 Determination of air content
- pressure method
ČSN EN 12 350-7, p. 5 Fresh concrete
123/13 Determination of bulk
density
ČSN EN 12390-7
ČSN EN 992
Concrete, lightweight
aggregate concrete
123/14 Determination of bulk
density
ČSN EN 12 350-6 Concrete
123/15 Determination of moisture
content and absorption
power
ČSN EN 1338, Annex E
ČSN EN 1339, Annex E
ČSN EN 1340, Annex E
Concrete, paving flags and
blocks, kerb units
123/16 Determination of
compressive strength of test
specimens and cored
specimens
ČSN EN 12390-3
ČSN EN 1354
ČSN EN 12504-1
ČSN EN 13791 p. 7 and 10,
Annex A and D
Concrete, lightweight
aggregate concrete
123/17 Determination of tensile
splitting strength
ČSN EN 12390-6
ČSN EN 1338, Annex F
Concrete, paving blocks
123/18 Determination of flexural
strength and fracture load
ČSN EN 1339, Annex F
ČSN EN 1521
ČSN EN 12390-5
Concrete, paving flags,
lightweight aggregate
concrete
123/19 Determination of resistance
to frost
ČSN 73 1322
ČSN EN 15304
Concrete, aerated concrete
123/20 Determination of concrete
resistance to chemical de-
icing substances (CHRL)
ČSN 73 1326
ČSN EN 13581
ČSN 73 1380
ČSN P CEN/TS 12390-9
Concrete, products for the
protection of concrete
structures
123/21 Determination of concrete
water tightness
IZP 123-15/2005 (ČSN 73 1321:1988)
ČSN EN 12390-8
Concrete, concrete products
123/22 Determination of water
absorption due to capillary
action
ČSN EN 772-11 Masonry units
123/23 Determination of density,
shrinkage and expansion
ČSN 73 1320 Concrete
123/24 Pressure test ČSN EN 826 Thermal insulating products
123/25 Determination of weight and
bulk density
ČSN EN 678
ČSN EN 1602
ČSN EN 772-4
ČSN EN 772-13
Aerated concrete, thermal
insulating products, brick
products
The Appendix is an integral part of
Certificate of Accreditation No. 73/2019 of 12/02/2019
Accredited entity according to ČSN EN ISO/IEC 17025:2018:
České vysoké učení technické v Praze Faculty of Civil Engineering – Testing Laboratory
Thákurova 7, 166 29 Praha 6
Page 3 of 16 11_01-P508_L-20130510
Ordinal number
1
Test procedure/ method name
Test procedure/ method identification
2
Tested object
123/26 Determination of
compressive strength
ČSN EN 679 Porous concrete
123/27 Determination of moisture
content and absorption
power
ČSN EN 772-10
ČSN EN 1353
ČSN 73 1357, part 2
ČSN EN 772-7
Aerated concrete, calcium
silicate masonry units, brick
products
123/28 Determination of weight,
water absorption and the
initial rate of water
absorption
ČSN 72 2603
ČSN EN 772-11
Brick products, concrete
masonry units, masonry
units
123/29 Determination of
compressive strength
ČSN EN 772-1+A1
Masonry units
123/30 Frost resistance test ČSN 72 2601, Annex A
ČSN EN 772-18
Brick products, masonry
units
123/31 Determination of capillary
water absorption
ČSN EN 1015-18
ČSN EN 480-5
ČSN EN 13580
Mortars, injection mortars,
additives, impregnations
123/32 Determination of weight and
porosity
ČSN EN 1015-10 Mortars
123/33 Test of compressive strength ČSN EN 1015-11
ČSN EN 12190
ČSN EN 13279-2
ČSN EN 13454-2+A1
ČSN EN 445
Mortars, binders, screeds,
injection mortars
123/34 Test of flexural strength ČSN EN 1015-11
ČSN EN 13279-2
ČSN EN 13454-2+A1
Mortars, screeds
123/35 Frost resistance test ČSN 72 2452 Mortars
123/36 Determination of density ČSN EN 1015-6 Mortars
123/37 Determination of grain size ČSN EN 1015-1
ČSN EN 12192-1
Mortars
123/38* Determination of adhesion
to the substrate
ČSN 73 6242, Annex B
ČSN EN 1015-12
ČSN EN 1542
ČSN EN 13279-2
Mortars
123/39 Determination of flexural
strength and compressive
strength
ČSN EN 13892-2 Screed materials
123/40* Determination of adhesion ČSN EN 13892-8 Screed materials
123/41 Frost resistance test ČSN 73 2579 Surface finish
123/42 Determination of tensile
strength perpendicular to
faces
ČSN EN 1607 Thermal insulating materials
The Appendix is an integral part of
Certificate of Accreditation No. 73/2019 of 12/02/2019
Accredited entity according to ČSN EN ISO/IEC 17025:2018:
České vysoké učení technické v Praze Faculty of Civil Engineering – Testing Laboratory
Thákurova 7, 166 29 Praha 6
Page 4 of 16 11_01-P508_L-20130510
Ordinal number
1
Test procedure/ method name
Test procedure/ method identification
2
Tested object
123/43 Determination of
dimensions
ČSN EN 1339, Annex C
ČSN EN 1338, Annex C
ČSN EN 1340, Annex C
ČSN EN 12085
ČSN EN 772-16
Concrete paving flags,
blocks and kerb units, brick
products, thermal insulation
products
123/44 Determination of resistance
to freezing/ thawing
ČSN EN 1338, Annex D
ČSN EN 1339, Annex D
ČSN EN 1340, Annex D
Concrete paving flags,
blocks and kerb units
123/45 Visual verification of cracks
and peeling
ČSN EN 1338, Annex J
ČSN EN 1339, Annex J
ČSN EN 1340, Annex J
Concrete paving flags,
blocks and kerb units
123/46 Determination of air content
of fresh mortar
ČSN EN 1015-7 Mortars, dry mortar mixtures
123/47 Determination of water
absorption by capillarity
ČSN EN 15801 Building materials and
products
123/48 Determination of water
absorption
ČSN EN 12808-5
ČSN EN 1062-3
Adhesives and mortars,
paints and varnishes
123/49 Determination of flexural
and compressive strength
ČSN EN 12808-3
ČSN 72 2071, p. 11.8
Adhesives, mortars and ash
123/50 Determination of moisture
content by drying at
elevated temperature
ČSN EN ISO 12570 Building materials and
products
123/51 Determination of
hygroscopic sorption
properties
ČSN EN ISO 12571 Building materials and
products
123/52 Determination of hygric
expansion coefficient
ČSN EN 13009 Building materials and
products
123/53 Determination of setting
time
ČSN EN 13294
ČSN EN 480-2
Mortars, products for the
protection and repair of
concrete structures
123/54* Determination of
carbonation depth
ČSN EN 14630 Mortars and concrete
1 Asterisk at the ordinal number identifies the tests, which the Laboratory is qualified to carry out outside the
permanent laboratory premises.
2 If the document identifying the test procedure is dated, only these specific procedures are used. If the
document identifying the test procedure is not dated, the latest edition of the specified procedure is used
(including any changes).
Explanations and abbreviations:
CEN - Comité Européen de Normalisation (European Committee for Standardization)
TS - Technical Specification
The Appendix is an integral part of
Certificate of Accreditation No. 73/2019 of 12/02/2019
Accredited entity according to ČSN EN ISO/IEC 17025:2018:
České vysoké učení technické v Praze Faculty of Civil Engineering – Testing Laboratory
Thákurova 7, 166 29 Praha 6
Page 5 of 16 11_01-P508_L-20130510
2. OL 124 Building Structures Laboratory
Tests:
Ordinal number
1
Test procedure/ method name
Test procedure/ method identification 2
Tested object
124/1 Testing of mould proofness
of building products and
materials
ČSN 72 4310 Building materials and
products
124/2 Determination of resistance
to moulds - assessment of
the effect of microorganisms
ČSN EN ISO 846, except
method C
Plastics
124/3 Measurement of diffusion
coefficient of radon
K 124/01-09 Water- and radon-proofing,
building materials
124/4 Measurement of diffusion
coefficient of radon
ISO/TS 11665-13 Water- and radon-proofing,
building materials
1 Asterisk at the ordinal number identifies the tests, which the Laboratory is qualified to carry out outside the
permanent laboratory premises.
2 If the document identifying the test procedure is dated, only these specific procedures are used. If the
document identifying the test procedure is not dated, the latest edition of the specified procedure is used
(including any changes).
Explanations and abbreviations:
K - Guideline (Internal Instruction) issued and approved before 01/07/1998 TS - Technical Specification
The Appendix is an integral part of
Certificate of Accreditation No. 73/2019 of 12/02/2019
Accredited entity according to ČSN EN ISO/IEC 17025:2018:
České vysoké učení technické v Praze Faculty of Civil Engineering – Testing Laboratory
Thákurova 7, 166 29 Praha 6
Page 6 of 16 11_01-P508_L-20130510
3. OL 132 Structural Mechanics Laboratory
Tests:
Ordinal number
1
Test procedure/ method name
Test procedure/ method identification 2
Tested object
132/1* Loading tests of building
structures
ČSN 73 2030 Buildings, industrial
buildings, machine
foundations, civil
engineering structures
132/2* Dynamic tests of building
structures
ČSN 73 2044 Buildings, industrial
buildings, machine
foundations, civil
engineering structures
132/3* Loading tests of bridges ČSN 73 2030
ČSN 73 6209
Road, railway and combined
bridges, culverts, overhead
crossings, pedestrian and
bicycle bridges and bridge-
like structures
132/4 Determination of flexural
strength of test specimens
IZP 132-01/2014 Mortars, cement- and
plaster-based composite
materials
132/5 Determination of
compressive strength of test
specimens
IZP 132-02/2014 Mortars, cement- and
plaster-based composite
materials
1 Asterisk at the ordinal number identifies the tests, which the Laboratory is qualified to carry out outside the
permanent laboratory premises.
2 If the document identifying the test procedure is dated, only these specific procedures are used. If the
document identifying the test procedure is not dated, the latest edition of the specified procedure is used
(including any changes).
Explanations and abbreviations:
IZP - Internal Test Instruction issued and approved after 01/01/2000
The Appendix is an integral part of
Certificate of Accreditation No. 73/2019 of 12/02/2019
Accredited entity according to ČSN EN ISO/IEC 17025:2018:
České vysoké učení technické v Praze Faculty of Civil Engineering – Testing Laboratory
Thákurova 7, 166 29 Praha 6
Page 7 of 16 11_01-P508_L-20130510
4. OL 133 Concrete Structures Laboratory
Tests:
Ordinal number
1
Test procedure/ method name
Test procedure/ method identification 2
Tested object
133/1 Determination of flexural
strength of concrete -
working diagram
ČSN EN 12390-5:2000 Concrete, fiber-reinforced
concrete
133/2 Determination of the
number of steel fibers in
hardened steel fiber concrete
IZP 133-02/2007 Steel fiber concrete
133/3 Determination of
compressive strength of test
specimens
ČSN EN 12390-3 Concrete, fiber-reinforced
concrete
133/4 Determination of tensile
splitting strength of test
specimens
ČSN EN 12390-6 Concrete, fiber-reinforced
concrete
133/5 Determination of secant
modulus of elasticity in
compression
ČSN EN 12390-13 Concrete, fiber-reinforced
concrete
1 Asterisk at the ordinal number identifies the tests, which the Laboratory is qualified to carry out outside the
permanent laboratory premises.
2 If the document identifying the test procedure is dated, only these specific procedures are used. If the
document identifying the test procedure is not dated, the latest edition of the specified procedure is used
(including any changes).
Explanations and abbreviations:
IZP - Internal Test Instruction issued and approved after 01/01/2000
The Appendix is an integral part of
Certificate of Accreditation No. 73/2019 of 12/02/2019
Accredited entity according to ČSN EN ISO/IEC 17025:2018:
České vysoké učení technické v Praze Faculty of Civil Engineering – Testing Laboratory
Thákurova 7, 166 29 Praha 6
Page 8 of 16 11_01-P508_L-20130510
5. OL 134 Steel Structures Laboratory
Tests:
Ordinal number
1
Test procedure/ method name
Test procedure/ method identification 2
Tested object
134/1 Tensile test ČSN EN ISO 6892-1 Steel elements
134/2 Charpy impact test ČSN ISO 148-1 Steel elements
134/3 Weldability test of metals IZP 134-01/2009 (ČSN 05 1312:1963)
Steel elements
1 Asterisk at the ordinal number identifies the tests, which the Laboratory is qualified to carry out outside the
permanent laboratory premises.
2 If the document identifying the test procedure is dated, only these specific procedures are used. If the
document identifying the test procedure is not dated, the latest edition of the specified procedure is used
(including any changes).
Explanations and abbreviations:
IZP - Internal Test Instruction issued and approved after 01/01/2000
The Appendix is an integral part of
Certificate of Accreditation No. 73/2019 of 12/02/2019
Accredited entity according to ČSN EN ISO/IEC 17025:2018:
České vysoké učení technické v Praze Faculty of Civil Engineering – Testing Laboratory
Thákurova 7, 166 29 Praha 6
Page 9 of 16 11_01-P508_L-20130510
6. OL 136 Road Structures Laboratory
Tests:
Ordinal number
1
Test procedure/ method name
Test procedure/ method identification 2
Tested object
136/1 Determination of particle size
distribution
ČSN EN 933-1 Aggregates
136/2 Determination of the
percentage of coarse aggregate
particles with shape index 3
and higher
ČSN EN 933-4 Aggregates
136/3 Determination of particle
density and water absorption
of aggregates
ČSN EN 1097-6, p. 7, 8 Aggregates
136/4 Determination of durability of
dense aggregates
ČSN EN 1367-2 Aggregates
136/5 Determination of resistance to
freezing and thawing of
aggregates
ČSN EN 1367-1 Aggregates
136/6 Test of resistance of
aggregates to fragmentation
ČSN EN 1097-2 Aggregates
136/7 Determination of density of
dense aggregates
ČSN EN 1097-6 Aggregates
136/8 Determination of voids in
aggregates
ČSN EN 1097-3 Aggregates
136/9 Penetration test ČSN EN 1426 Bitumen
136/10 Determination of the softening
point
ČSN EN 1427 Bitumen
136/11 Determination of force
ductility
ČSN EN 13589 Bitumen
136/12 Reserved
136/13 Pull-off test for adhesion of
bitumen
ČSN 73 6161 Bitumen
136/14 Tests of finished layer - degree
of compaction, shear strength
and void characteristics
ČSN 73 6160, p. 7.2 (except
7.2.b), p. 7.3, p. 7.4
Bituminous mixtures
136/15 Determination of soluble
binder content, including
sample preparation
ČSN EN 12697-1
ČSN EN 12697-28
Bituminous mixtures
136/16 Test of particle size
distribution, including
preparation of samples
ČSN EN 12697-2
ČSN EN 12697-28
Bituminous mixtures
136/17 Determination of the
maximum density
ČSN EN 12697-5 Bituminous mixtures
136/18 Determination of bulk density
of bituminous specimens
ČSN EN 12697-6 Bituminous mixtures
136/19 Determination of the thickness
of a bituminous pavement
ČSN EN 12697-36, p. 4.1 Bituminous mixtures
The Appendix is an integral part of
Certificate of Accreditation No. 73/2019 of 12/02/2019
Accredited entity according to ČSN EN ISO/IEC 17025:2018:
České vysoké učení technické v Praze Faculty of Civil Engineering – Testing Laboratory
Thákurova 7, 166 29 Praha 6
Page 10 of 16 11_01-P508_L-20130510
Ordinal number
1
Test procedure/ method name
Test procedure/ method identification 2
Tested object
136/20 Determination of the air void
content of bituminous mixture
ČSN EN 12697-8 Bituminous mixtures
136/21 Determination of the water
sensitivity of bituminous
specimen, including
preparation of samples
ČSN EN 12697-12
ČSN EN 12697-30
Bituminous mixtures
136/22 Determination of particle loss
of porous asphalt specimen,
including preparation of
samples
ČSN EN 12697-17
ČSN EN 12697-30
Bituminous mixtures
136/23 Determination of the binder
drainage
ČSN EN 12697-18 Bituminous mixtures
136/24 Determination of hardness
number using cube or
Marshall specimen
ČSN EN 12697-20 Bituminous mixtures
136/25 Determination of hardness
number using plate specimen
ČSN EN 12697-21 Bituminous mixtures
136/26 Wheel tracking test, including
preparation of samples
ČSN EN 12697-22+A1
ČSN EN 12697-33+A1
Bituminous mixtures
136/27 Determination of indirect
tensile strength, including
preparation of test specimens
ČSN EN 12697-23
ČSN EN 12697-30
Bituminous mixtures
136/28 Determination of the
dimensions of bituminous
specimens
ČSN EN 12697-29 Bituminous mixtures
136/29 Marshall test, including
preparation of samples
ČSN EN 12697-30
ČSN EN 12697-34
Bituminous mixtures
136/30 Determination of stiffness -
four-point bend test
ČSN EN 12697-26, Annex B Bituminous mixtures
136/31 Determination of stiffness -
Indirect tensile test of
cylindrical test specimens
ČSN EN 12697-26, Annex C Bituminous mixtures
136/32 Determination of fatigue
resistance - four-point bend
test
ČSN EN 12697-24, Annex D Bituminous mixtures
136/33 Reserved
136/34 Determination of reference
density and water content –
Proctor test
ČSN EN 13286-2 Unbound and
hydraulically bound
mixtures
136/35 Determination of bulk density
by a membrane stereometer
ČSN 72 1010, method D-1 Soils
136/36 Determination of moisture
content
ČSN EN ISO 17892-1 Soils
136/37* Static loading test ČSN 72 1006, Annex A Soils
The Appendix is an integral part of
Certificate of Accreditation No. 73/2019 of 12/02/2019
Accredited entity according to ČSN EN ISO/IEC 17025:2018:
České vysoké učení technické v Praze Faculty of Civil Engineering – Testing Laboratory
Thákurova 7, 166 29 Praha 6
Page 11 of 16 11_01-P508_L-20130510
Ordinal number
1
Test procedure/ method name
Test procedure/ method identification 2
Tested object
136/38 Determination of the indirect
tensile strength
ČSN EN 13286-42 Unbound and
hydraulically bound
mixtures
1 Asterisk at the ordinal number identifies the tests, which the Laboratory is qualified to carry out outside the
permanent laboratory premises.
2 If the document identifying the test procedure is dated, only these specific procedures are used. If the
document identifying the test procedure is not dated, the latest edition of the specified procedure is used
(including any changes).
The Appendix is an integral part of
Certificate of Accreditation No. 73/2019 of 12/02/2019
Accredited entity according to ČSN EN ISO/IEC 17025:2018:
České vysoké učení technické v Praze Faculty of Civil Engineering – Testing Laboratory
Thákurova 7, 166 29 Praha 6
Page 12 of 16 11_01-P508_L-20130510
7. OL 137 Railway Structures Laboratory
Tests:
Ordinal number
1
Test procedure/ method name
Test procedure/ method identification
2
Tested object
137/1* Static loading test ČSN 72 1006, Annex A, B
SŽDC S4, Annex 5
Soils
137/2* Impact loading test by light dynamic plate (equipment of Group C)
ČSN 736192 Soils
137/3* Determination of bulk
density by a membrane
stereometer
ČSN 72 1010, method D-1 Soils
137/4 Determination of moisture
content
ČSN EN ISO 17892-1 Soils
137/5* Measurement of noise ČSN ISO 1996-1
ČSN ISO 1996-2
MoH CR Bulletin, Part
11/2017
Non-working environment
137/6 Determination of static
rigidity of anti-vibration
mats
OTP SŽDC No. 1168/2009-S,
Annex No. 2
Anti-vibration mats
137/7 Determination of resistance
to cyclic loading
OTP SŽDC No. 1168/2009-S,
Annex No. 4
Anti-vibration mats
137/8 Determination of resistance
to cyclic freezing and
thawing
OTP SŽDC No. 1168/2009-S,
Annex No. 5
Anti-vibration mats
137/9 Vertical load test of integral
or glued parts of fastening
systems
ČSN EN 13481-2, Annex A
ČSN EN 13146-10
Track
1 Asterisk at the ordinal number identifies the tests, which the Laboratory is qualified to carry out outside the
permanent laboratory premises.
2 If the document identifying the test procedure is dated, only these specific procedures are used. If
the document identifying the test procedure is not dated, the latest edition of the specified procedure
is used (including any changes).
Explanations and abbreviations:
OTP - General Technical Specifications
SŽDC - Railway Infrastructure Administration
MoH CR Bulletin, Part 11/2017 Guideline for the measurement and evaluation of noise in non-
workplace environment
The Appendix is an integral part of
Certificate of Accreditation No. 73/2019 of 12/02/2019
Accredited entity according to ČSN EN ISO/IEC 17025:2018:
České vysoké učení technické v Praze Faculty of Civil Engineering – Testing Laboratory
Thákurova 7, 166 29 Praha 6
Page 13 of 16 11_01-P508_L-20130510
8. OL 181 Experimental Centre Laboratory (FSv)
Tests:
Ordinal number
1
Test procedure/ method name
Test procedure/ method identification
2
Tested object
181/1* Loading tests of building
structures
ČSN 73 2030 Building structures and
their parts
181/2* Dynamic tests of building
structures
ČSN 73 2044 Building structures and
their parts
181/3* Loading tests of bridges ČSN 73 2030
ČSN 73 6209
Road, railway, water and
similar bridges
181/4 to
21
Reserved
181/22 Determination of
compressive strength
ČSN EN 12390-3 Structural concrete,
concrete products
181/23 Determination of flexural
strength
ČSN EN 12390-5 Structural concrete,
concrete products
181/24 Determination of tensile
splitting strength
ČSN EN 12390-6 Structural concrete,
concrete products
181/25 Determination of density ČSN EN 12390-7 Structural concrete,
concrete products
181/26 Determination of depth of
penetration of water under
pressure
ČSN EN 12390-8 Structural concrete,
concrete products
181/27 Determination of secant
modulus of elasticity in
compression
ČSN EN 12390-13 Structural concrete,
concrete products
181/28 Determination of resistance
to chemical de-icing
substances (CHRL)
ČSN 73 1326 Structural concrete,
concrete products
181/29 Determination of frost
resistance
ČSN 73 1322 Structural concrete,
concrete products
1 Asterisk at the ordinal number identifies the tests, which the Laboratory is qualified to carry out outside the
permanent laboratory premises.
2 If the document identifying the test procedure is dated, only these specific procedures are used. If the
document identifying the test procedure is not dated, the latest edition of the specified procedure is used
(including any changes).
The Appendix is an integral part of
Certificate of Accreditation No. 73/2019 of 12/02/2019
Accredited entity according to ČSN EN ISO/IEC 17025:2018:
České vysoké učení technické v Praze Faculty of Civil Engineering – Testing Laboratory
Thákurova 7, 166 29 Praha 6
Page 14 of 16 11_01-P508_L-20130510
9. OL 181 Experimental Centre Laboratory (UCEEB)
Tests:
Ordinal number
1
Test procedure/ method name
Test procedure/ method identification
2 Tested object
181/1 to 3 Reserved
181/4* Determination of qualitative
parameters for visual
classification according to
strength
ČSN 73 2824-1, except chap.
7
Structural timber
181/5* Check of dimensions of
structural components
(accuracy)
ČSN 73 0212-5 Building materials and
products
181/6 Determination of modulus
of elasticity and bending
strength
ČSN EN 408 Structural timber, glued
laminated timber
181/7 Determination of
mechanical durability and
stability
- by calculation
ČSN EN 1995-1-1
ČSN EN 1995-1-2
Timber structures and their
parts
- test ČSN 73 2030
ČSN EN 380
181/8* Determination of airborne
sound insulation
ČSN EN ISO 10140-1
ČSN EN ISO 10140-2
ČSN EN ISO 10140-4
ČSN EN ISO 16283-1
ČSN EN ISO 16283-3
ČSN EN ISO 717-1
Building elements and
buildings
181/9* Determination of impact
sound insulation
ČSN EN ISO 10140-1
ČSN EN ISO 10140-3
ČSN EN ISO 10140-4
ČSN EN ISO 16283-2
ČSN EN ISO 717-2
Building elements and
buildings
181/10 Determination of flanking
transmission of airborne and
impact sound by laboratory
measurement
ČSN EN ISO 10848-1
ČSN EN ISO 10848-2
ČSN EN ISO 717-1
ČSN EN ISO 717-2
Building elements
181/11* Measurement of
reverberation time
ČSN EN ISO 3382-1
ČSN EN ISO 3382-2
Building spaces
181/12* Measurement of noise ČSN ISO 1996-1
ČSN ISO 1996-2
ČSN EN ISO 16032
MoH CR Bulletin, Part
11/2017
Non-occupational
environment
181/13* Measurement of noise ČSN EN ISO 9612
MoH CR Bulletin, Part 4/2013 Occupational environment
The Appendix is an integral part of
Certificate of Accreditation No. 73/2019 of 12/02/2019
Accredited entity according to ČSN EN ISO/IEC 17025:2018:
České vysoké učení technické v Praze Faculty of Civil Engineering – Testing Laboratory
Thákurova 7, 166 29 Praha 6
Page 15 of 16 11_01-P508_L-20130510
Ordinal number
1
Test procedure/ method name
Test procedure/ method identification
2 Tested object
181/14 Determination of thermal
resistance by means of heat
flow meter
ČSN EN 12667 Building materials and
products
181/15 Determination of moisture
content by drying at
elevated temperature
ČSN EN ISO 12570 Building materials and
products
181/16 Determination of water
vapour transmission
properties
ČSN EN ISO 12572 Building materials and
products
181/17 Determination of thermal
performance
ČSN EN ISO 9806, except p.
6 to 19
Solar thermal collectors
181/18 Determination of
mechanical properties
ČSN EN 1886, except p. 10,
11
Air-handling unit casing
181/19 Measurement of
performance parameters
ČSN EN 308 Heat exchangers for heat
recovery in air handling
technology
1 Asterisk at the ordinal number identifies the tests, which the Laboratory is qualified to carry out outside the
permanent laboratory premises.
2 If the document identifying the test procedure is dated, only these specific procedures are used. If
the document identifying the test procedure is not dated, the latest edition of the specified procedure
is used (including any changes).
Explanations and abbreviations:
MoH CR Bulletin, Part 4/2013 Guideline for the measurement and evaluation of noise and
vibrations at workplace and vibrations in protected indoor areas of
buildings
MoH CR Bulletin, Part 11/2017 Guideline for the measurement and evaluation of noise in non-
workplace environment
The Appendix is an integral part of
Certificate of Accreditation No. 73/2019 of 12/02/2019
Accredited entity according to ČSN EN ISO/IEC 17025:2018:
České vysoké učení technické v Praze Faculty of Civil Engineering – Testing Laboratory
Thákurova 7, 166 29 Praha 6
Page 16 of 16 11_01-P508_L-20130510
10. OL 182 Experimental Geotechnics Centre Laboratory
Tests:
Ordinal number
1
Test procedure/ method name
Test procedure/ method identification 2
Tested object
182/1 Determination of the water
content
ČSN EN ISO 17892-1 Soils
182/2 Determination of density ČSN EN ISO 17892-2, p. 5.1,
5.2
Soils
182/3 Determination of apparent
density of solid particles
ČSN EN ISO 17892-3 Soils
182/4 Determination of uniaxial
compressive strength ČSN EN 1926 Rocks, natural building
stone
182/5 Determination of Atteberg
limits
ČSN EN ISO 17892-12,
p. 5.3, p. 5.5
Soils
1 Asterisk at the ordinal number identifies the tests, which the Laboratory is qualified to carry out outside the
permanent laboratory premises.
2 If the document identifying the test procedure is dated, only these specific procedures are used. If
the document identifying the test procedure is not dated, the latest edition of the specified procedure
