Montáže Čakovice s.r.o. (Igor Botlík) - SEL · Zařízení SEL pro přenos stavů MONTÁŽE...

MONTÁŽE ČAKOVICEs.r.o .

Přenos a zpracování dat za řízeními SEL

Montáže Čakovice s.r.o. (Igor Botlík)

strana 1


Použití SEL 2505/6, 2515/6, 2594/5

� Náhrada přímého propojení DI DO

DO1DO2…..DO8

DI1DI2…..DI8

DI1DI2…..DI8

DO1DO2…..DO8

IED 1 IED 20

1

0

0

1

0

1

0

1

1

0

1

NE! (při větších vzdálenostech)

strana 2


Zařízení SEL pro p řenos stav ů

Connected Device ProtocolSurface Mount

Rack Mount

SEL-2505 or SEL-2506 Remote 8I/O Module, Relay, or SEL-2100

Logic Processor

SEL MIRRORED BITS®

CommunicationsSEL-2505 SEL-2506

SEL-2594 Contact Transfer 8I/O Module or SEL-2595 Teleprotection Terminal Through Multiplexers

IEEE C37.94 SEL-2594 SEL-2595

SEL-2411 PAC

SEL-2440 DPAC

SEL MIRRORED BITS®

Communications

….

-

ano

-

ano

strana 3


Použití SEL 2505/6, 2594/5

� Nastavení SEL 2505/6

FIBER OPTIC CONTROL SWITCHESON

OFFTX RX

190-2911-02

10 123456789

10 9 8 7 6 5 4 3 2 1PROTOCOL/BAUD 7 & 8 5 & 6 3 & 4 1 & 2 RX_ADD TX_ADD

=1

=2

=3

=4

=1

=2

=3

=4FAST

SECURE

OUTPUT CONTACT MODE

= RESERVED

= MB8/9600

= MB8/19200

= MB8/38400

strana 4


Peer-to -Peer

� MIRRORED BITS®

� Jednoduchá a bezpečná metoda přenosu log. stavů mezi zařízeními

� Komunikace přes různá media � Optické vlákno

� Multiplexní digitální sí ť

� Analogové modemy

� Rádiová sí ť (point-to-point)

� Univerzální použití

� Implementace (využitím SEL HW) ve všech SEL zař.

� Low-cost řešenístrana 5


MIRRORED BITS®

� Možnost vysílat a přijímat MB na dvou portech

� Monitorování jednotlivých stavů, events protokol výpadků pomocí příkazu „COMM“, buffer 255 záznamů, nastavení loop-back pro testování,…

� Možnost přímého datového propojení 2 komunikačně nekompatibilních zařízení či zařízení bez komunikace

� Zpracování pomocí logického enginu IEC 61131

� Rychlost až 38.400 bps (transportní zpoždění typ. 4,2ms), plně duplexní, sériová asynchronní komunikace, cyklické 4B telegramy

strana 6


MIRRORED BITS® v zařízeních SEL

� Využití protokolu i pro více IED

strana 7


MIRRORED BITS®

� Nastavení

strana 8


Použití SEL 2505/6, 2515/6, 2594/5

� Přímý přenos single/MM optikou

SEL-2505

Non-MIRRORED

BITS

Relay

Non-MIRRORED

BITS

Relay

RX

TX

TX

RXSEL-2505

Contact I/O Contact I/OSingle-ModeFiber Link

Up to 80 km

strana 9


Použití SEL 2505/6, 2515/6, 2594/5

� Přenos přes multiplexer ICON protokolem IEEE C37.94

SEL-2505 SEL-2505

Contact I/O

Fiber Link

SONET Multiplexer

SONET Multiplexer

SEL-2800

Non-MIRRORED BITS Relay


Contact I/O

SEL-2800

SEL-2594 SEL-2594

Contact I/O

Fiber Link

SONETMultiplexer

SONETMultiplexer

Non-MIRRORED

BITS RelayNon-MIRRORED

BITS Relay

Contact I/O

ICON

strana 10


Použití SEL 2505/6, 2515/6, 2594/5

� Kombinovaná zapojení

SEL-2505


MIRRORED BITS Relay

MIRRORED BITS Relay

SCADA

IEC 61850 GOOSE

MIRRORED BITS

IEC 61850

Contact I/O

SEL-2505

MIRRORED BITS Relay


IEC 61850 GOOSE

MIRRORED BITS

IEC 61850

1)

2)


SCADA

Contact I/O

strana 11


Použití SEL 2505/6, 2515/6, 2594/5

� Kombinované zapojení se SEL- 2411 PAC

SEL-2505


SE

L-24

11


IEC 61850 GOOSE

MIRRORED BITS

IEC 618503)


SCADA

IEC 61850 GOOSE Contact I/O

strana 12

Implement Fast, Reliable AutomationApply the Rugged SEL-2411

Programmable Automation Controller

Withstands Extreme Conditions

Flexible – Install Up to FourSELECT™ I/O Cards

Match Your Application WithSELECT I/O Cards

Card DescriptionSELECT I/O

Card Designation

Maximum Cards PerSEL-2411

8 Analog Inputs 8 AI 4

4 Analog Inputs / 4 Analog Outputs

4 AI / 4 AO 2

8 Digital Inputs 8 DI 4

8 Digital Outputs 8 DO 4

4 Digital Inputs / 4 Digital Outputs

4 DI / 4 DO 4

4 AC Current Inputs 4 ACI 1

Three-Phase AC Voltage Inputs

3 AVI 1

EIA-232 or EIA-485 Port EIA-232 / -485 1

Additional Key Benefits

� Quickly set and commission with ACSELERATOR® QuickSet SEL-5030 Software

� SER, DFR

� Implement distributed high-speed logic schemes with SEL MIRRORED BITS®

communications links

� Communicate via Ethernet with Telnet, FTP, Modbus® TCP, and DNP3 LAN / WAN

Quickly Set With ACSELERATOR

QuickSet Software

Application Example: Breaker Monitoring, Status Panel, and

Transducers

DCS or SCADA Master

Ethernet Switch

Application Example: Ethernet Network Connection to DCS or SCADA

DCS or SCADA Master

Application Example: EIA -485 Multidrop Connection to DCS or SCADA

Diagnose System Problems With SER

� Time-tag changes of DI to nearest millisecond

� SER is important and useful

� Analyze system disturbances

� Understand sequence to understand problems

� Coordinate with time-tagged oscillographic or digital fault recorder (DFR) records

� Station-wide / system-wide SER reporting

� DNP3 serial or LAN / WAN messages

� SEL Fast Messages to SEL-2032 Communications Processor or SEL-3351 System Computing Platform

Example SER Report

Point Description

Data Source / LocationTime-Tagged to Nearest Millisecond

Element NameNew State

� 32 latch bits

� 64 SELOGIC variables and timers

� 32 front-panel display points

� 32 local bits for front-panel controls

� 32 remote bits for remote control

Implement Local Automatic Control

User-Configurable

Labels

LED Indicators

PushbuttonsLCD Display

Install AC Voltage Input Card and Activate Built-In Functions

� VAB, VBC, VCA or VAN, VBN, VCN, VG magnitudes (V), and phase angles (degrees)

� Negative-sequence (3V2)

� System frequency (Hz)

� Event reports

Example applications

� Undervoltage or underfrequency load shedding

� Voltage control

S E L - 2 4 1 1

Install AC Current Input Card and Activate Built-In Functions

� Line currents IA, IB, IC, and IN magnitudes (A), and phase angles (deg)

� IG (Residual Ground Fault Current) magnitude (A) and phase angle (deg)

� Negative-sequence current (3I2) magnitude

� System frequency (Hz)

� Event reports

Example applications

� Fault recording

� Underfrequency load shedding

� Protection backup

S E L - 2 4 1 1

Install Both AC Current and Voltage Input Cards for Built-In Functions

� All of the voltage and current functions

� Real power (kW)

� Reactive power (kVAR)

� Apparent power (kVA)

� Power factorExample applications

� VAR control

� SCADA data

� PF control

� Fault recording

S E L - 2 4 1 1

AC Input Oscillograph

SEL-2411 Summary

� Base unit has 3 DO, 2 DI, and 4 card slots

� Flexible SELECT I/O cards provide many options

� 37 I/O points maximum per SEL-2411

� Many protocol options

SEL-2411 Summary

� Best temperature, vibration, and electrical withstand capabilities

� Highest reliability

� Lowest overall cost

� SEL worldwide, ten-year product warranty


SEL DPAC

� $960 for 48 utility-grade I/O points = $20 point� Microsecond timing� Fast and powerful processing� Flexible communications and protocols

strana 31


DPAC - robustn í provedení I/O a mnohem v íce!

� Vysoká spolehlivost a robustní konstrukce� Kritická hlášení � Flexibilní digitální I / O výběr� Běží v extrémních podmínkách� Pohodlné na údržbu a podporu� Jednoduché uvedení do provozu� Jednoduché programování SEL Logic� Použití i jako samostatný kontroler nebo

SER (DFR) pro různé aplikacestrana 32

Withstands Extreme Conditions

Designed, built, and tested to meet mission-critical IEEE and IEC protective relay standards for substations

DPAC Functional Block Diagram

New Features

• 64 SELOGIC® control equation variables

• SNTP time synchronization

• 5 DNP3 sessions

• 2 Modbus® sessions

Flexible I/O Configuration to Match Your Needs

• Available I/O configurations

♦ 32 DI and 16 DO

♦ 16 DI and 32 standard DO

♦ 16 DI, 16 standard DO, and 16 high-current DO

♦ 48 DI

• Digital inputs support ac or dc control signals

• Digital input debounce settings

Mounting Options

Rack Panel

Surface DIN Rail

Diagnose System Problems With SER

• Time-tag DI changes to nearest microsecond

• SER is important and useful

♦ Analyze system disturbances

♦ Understand sequence to understand problems

♦ Coordinate with DFR records

• Station-wide / system-wide SER reporting

♦ DNP3 serial or LAN / WAN messages

♦ SEL Fast Messages to SEL-2032 or SEL-3530

Implement Local Automatic ControlSELOGIC Control Equation Functions

• 32 SELOGIC math variables (MVs)

• 64 SELOGIC variables (SVs and SVTs)

• 32 local bits

• 32 remote bits

• 32 nonvolatile latch bits

• 32 up / down counters

• 128 remote analog points

Flexible Connectivity for Complete Integration

• Dual Ethernet ports (copper RJ45 or fiber LC)

• Integrated Ethernet switch, which allows daisy chaining or redundancy

• Dual serial ports

♦ Single EIA-232

♦ Single EIA-232, EIA-485, or fiber-optic V-pin or ST® connectors

Serial (Copper or Fiber)Communications Protocols

• SEL ASCII, Fast Meter, Fast Operate, Fast Message, Fast SER

• SEL MIRRORED BITS® communications

• Compressed ASCII

• SEL Messenger Points for SEL-3010 Event Messenger

• Modbus RTU

• DNP3

Dual Ethernet (Copper or Fiber) Communications Protocols

• Modbus TCP

• FTP, Telnet, Ping

• DNP3 LAN / WAN

• IEC 61850 (optional)

Quickly Set With ACSELERATOR

QuickSet ® SEL-5030 Software

Program With Standard Logic Gates Using the Graphical Logic Editor

DPAC Summary

• Lowest overall cost for 48 I/O points

• Many protocol options

• Highest reliability

• Detailed analysis with SER

• SEL worldwide, 10-year product warranty


Děkuji za pozornost.

strana 46

Date post:	14-Jan-2020
Category:	Documents
Upload:	others
View:	2 times
Download:	0 times

Montáže Čakovice s.r.o. (Igor Botlík) - SEL · Zařízení SEL pro přenos stavů MONTÁŽE...

Documents